Terra Universal - Critical Environment Solutions
Preferred Client

Protector Combination Glove Boxes
by Labconco
Combination Glove Box
The Labconco Protector Combination Glove Box
  • Provide an enclosed environment for handling both hazardous substances and atmosphere-sensitive materials
  • Factory-leak tested with a mass spectrometer while pressurized with Helium at 5 inches of water gauge
  • Large viewing area, 36” W x 27.6” H (914 mm x 701 mm) for maximum viewing capabilities
  • Particulate containment of less than 20 nanograms per cubic meter
  • Fast “clean-up” time
  • Airborne particulate cleanliness (measured under positive and negative pressures per ISO 14644-1 test method) exceeds ISO Class 5 conditions and achieves ISO Class 4 conditions
  • Built in blower with speed control capable of airflow from 15 CFM to 85 CFM (25.5 m³/hr to 144.4 m³/hr)
  • Exceeds Class 1 atmosphere containment conditions for oxygen permeation less than 1.67 ppm/min per ISO 10648-2 test method
  • Automatic control of the main chamber pressure, main chamber evacuation and filling cycles, and transfer chamber evacuation and filling cycles
  • Input/Output port for optional AtmosPure Re-Gen Gas Purifier
  • Factory-installed, rear-mounted, low profile stainless steel pressure relief bubbler at ±6 inches of water gauge

Protector Combination Glove Boxes provides an enclosed environment for handling both hazardous substances and atmosphere-sensitive materials. With a HEPA inlet filter, these glove boxes can provide a particulate free internal environment.

A “Combination” Glove Box

Closure of two internal valves converts the box to a controlled atmosphere glove box that can be pressurized up to ±5 inches water gauge achieving a leak-tight inert atmosphere. When atmosphere-sensitive procedures are complete, opening the two internal valves allows air from inside the box to pass through a HEPA outlet filter and optional second HEPA or Carbon outlet filter before exhausting via a ductwork to the outside. The physical barrier and filtration system of these boxes protects the user from exposure to hazardous materials. Thus taking the concept of a Protector Filtered Glove Box and combining it with a Protector Controlled Atmosphere Glove Box.

Two Types of Material

The fiberglass-lined models feature a one-piece molded fiberglass liner with clear acrylic inner and outer transfer chamber doors. This model has been performance tested to maintain oxygen levels as low as 0.4 ppm and moisture levels as low as 2 ppm. The oxygen permeation is less than 0.3 ppm/min per ISO 10648-2 and illumination exceeds 120 footcandles.

The stainless steel-lined models feature a Type 304 stainless steel liner with Type 304 stainless steel inner and outer transfer chamber doors. Type 304 stainless steel material also comprises the front panel. This model has been performance tested to maintain oxygen levels as low as 0.2 ppm and moisture levels as low as 1 ppm. The oxygen permeation is less than 0.16 ppm/min per ISO 10648-2 and illumination exceeds 80 footcandles.

AtmosPure Re-Gen as Purifier

This gas purifier maintains ultrapure inert atmosphere within the Protector® Controlled Atmosphere Glove Boxes. It has the capacity to remove 5 liters of oxygen gas (13,500 ppm) and 660 grams of moisture (water vapor) which is equivalent to 18 million ppm. The regeneration is, in turn, completed in 13 hours. Additionally, the leak rate is ± .000001 mL/sec.

Protector Combination Glove Boxes Also Features:

Space saving inner and outer transfer chamber doors that pivot upward and an interior left-hand side wall-mounted pass-through plug for on-site installation of an optional accessory such as electrical outlet, RS-232 port, gas/liquid port, or port for oxygen or moisture monitor. Additionally, there is an interior right-hand side wall-mounted electrical receptacle with a 10 amp circuit load. The glove box also comes with a pair of neoprene gloves, two 8” (203 mm) ID epoxy-coated aluminum, double grooved glove ports, and two 25-watt florescent lights.
Specifications

 

 Domestic or International
Specifications		 Protector Fiberglass Combination Glove Box Protector Stainless Steel Combination Glove Box Protector Stainless Steel Double Combination Glove Boxes
Item Dimensions Domestic: 62.4”W x 37.6”D x 46.4”H
(1585 mm x 955 mm x 1179 mm)		 62.4”W x 37.6”D x 46.4”H
(1585 mm x 955 mm x 1179 mm)		 108.9”W x 37.6”D x 46.4”H
(2766 mm x 955 mm x 1179 mm)
International: 62.4”W x 37.6”D x 46.4”H
(1585 mm x 955 mm x 1179 mm)		 62.4”W x 37.6”D x 46.4”H
(1585 mm x 955 mm x 1179 mm)		 108.9”W x 37.6”D x 46.4”H
(2766 mm x 955 mm x 1179 mm)
Electrical Specifications Domestic: 115V; 50/60Hz, 10 Amps 115V; 50/60Hz, 10 Amps 115V; 50/60Hz, 10 Amps
International: 230V; 50/60Hz, 10 Amps 230V; 50/60Hz, 10 Amps 230V; 50/60Hz, 10 Amps
Filter Type Domestic: HEPA HEPA HEPA
International: HEPA HEPA HEPA
Number of Glove Ports Domestic: 2 2 4
International: 2 2 4
Primary Applications Domestic: Working with both Hazardous and Atmosphere-Sensitive Materials Working with both Hazardous and Atmosphere-Sensitive Materials Working with both Hazardous and Atmosphere-Sensitive Materials
International: Working with both Hazardous and Atmosphere-Sensitive Materials Working with both Hazardous and Atmosphere-Sensitive Materials Working with both Hazardous and Atmosphere-Sensitive Materials
Liner Material Domestic: Fiberglass Steel Steel
International: Fiberglass Steel Steel
Interior Working Domestic: 35.5” (902 mm)
 35.5” (902 mm) 35.5” (902 mm)
Width International: 35.5” (902 mm) 35.5” (902 mm) 35.5” (902 mm)
Required Accessories Domestic: Supporting Base Supporting Base Supporting Base
International: Supporting Base Supporting Base Supporting Base
Built-In Domestic : None None None
Options International: None None None
Compliance

 

 Domestic: ETL Listing, UL 61010-1 and CAN/CSA C22.2 No.1010.1 conformity ETL Listing, UL 61010-1 and CAN/CSA C22.2 No.1010.1 conformity ETL Listing, UL 61010-1 and CAN/CSA C22.2 No.1010.1 conformity
International: CE Conformity Marking CE Conformity Marking CE Conformity Marking
Ordering Information
Protector Combination Glove Boxes
Type Power Supply Fiberglass 304 Stainless Steel
Labconco # Cat. # $/Each Labconco # Cat. # $/Each
Single Models
(2 glove ports)		 120 VAC, 60 Hz 5080060 3644-15 Login 5080160 3644-16 Login
220VAC, 50/60Hz 5080065
5080070
5080075
5080080		 3644-15-220 Login 5080165
5080170
5080175
5080180		 3644-16-220 Login
Twin Models
(4 glove ports)		 120 VAC, 60 Hz — — — 5080162 3644-17 Login
220VAC, 50/60Hz — — — 5080167
5080172
5080177
5080182		 3644-17-220 Login
Required Accessories
Adjustable Height Mobile Base Stand
Adjustable Height Mobile Base Stand with 5" (127 mm) casters has durable 2" (51 mm) tubular glacier white epoxy-coated steel frame with permanently-mounted black laminate hard board work surface. Includes lower shelf, 47" w x 18" d (1194 mm x 457 mm), to accommodate accessory equipment such as a pump. Telescoping legs adjust in 1" (25 mm) increments to seven overall height positions from 33" to 40" (838 mm x 1016 mm).
Overall dimensions: 60" W x 31" D (1524 mm x 787 mm).
Labconco # Cat. # $/Each
5235500 3643-22 Login
  Adjustable Height Stationary Base Stand
Adjustable Height Stationary Base Stand with leveling feet has durable 2" (51 mm) tubular glacier white epoxy-coated steel frame with permanently-mounted black laminate hard board work surface. Includes lower shelf, 47" w x 18" d (1194 mm x 457 mm), to accommodate accessory equipment such as a pump. Telescoping legs adjust in 1" (25 mm) increments to seven overall height positions from 33" to 40" (838 mm x 1016 mm).
Overall dimensions: 60" W x 31" D (1524 mm  x 787 mm).
Labconco # Cat. # $/Each
5235501 3643-23 Login
     
Double Glove Box Mobile Base Stand
Double Glove Box Mobile Base Stand has epoxy-coated welded steel base with black phenolic laminate work surface. Height is adjustable, and lower shelf provides extra space.
Labconco # Cat. # $/Each
5062020 3643-24 Login

Inert Gas for Filling
A gas source is necessary to operate the glove box. Follow the link for more details on Terra Universal's Nitrogen Generator.

  

Vacuum Source:
Labconco offers Rotary Vane Direct Drive Vacuum Pumps to provide a reliable vacuum source. These pumps are available with displacement capacities of 117 or 195 liters per minute (at 60 Hz).

Terra Universal Offers several vacuum chambers and controllers to meet your vacuum source needs. (Insert link to Environmental and Vacuum Chambers section on the Terra Universal Website)

  Labconco # Cat. # $/Each
Direct Drive Rotary Vane
Vacuum Pumps-115 V
(Includes 115V NEMA 5-15P Plug)		 147210 3643-79 Login
Direct Drive Rotary Vane
Vacuum Pumps-230 V
(Includes 230V NEMA 6-15P Plug) 		7739400 3643-80 Login
Direct Drive Rotary Vane
Vacuum Pumps-230 V
(Includes 230V reverse IEC Plug)		 7739402 3643-81 Login
 
Nitrogen Membrane (See specification table below)
Dimensions
W" x D" x H" (mm)		 Uncrated Weight
lbs. (kg)		 Flow Range* Cat. # $/Each
18 x 18 x 81.25
(457 x 457 x 2064)
(including 1.25", 32 mm,  for leveling feet) 		157
(71)		 0-400 SCFH 2700-09A Login
24 x 12 x 49.25
(610 x 305 x 1251)
(including 1.25", 32 mm,  for leveling feet)		 96
(44)		 0-100 SCFH 2700-11A Login
20 x 12 x 35.5
(508 x 305 x 902)
(including 1.25", 32 mm, for leveling feet)		 58
(26)		 0-10 SCFH 2700-12A Login
* For 99% N2 purity. With 100psi inlet pressure
Replacement Filter Elements
1-µm Filter 2700-15 Login
0.025µm Coalescing Filter 2700-16 Login
Corresponding Options
AtmosPure Re-Gen Gas Purifier
AtmosPure Re-Gen gas purifier maintains ultrapure inert atm. in controlled atmosphere glove boxes. Capacity to remove 5L of O2 (13,500 ppm) and 660g H2O (18 mill. ppm). Regen. completed in 13 hrs. Leaks ≤1 x 10-6 ml/sec. 5lb (2268 g.) copper catalyst/5lb (2268 g.) molecular sieve. 115V/50/60Hz and 230V/50/60Hz
  Labconco # Cat. # $/Each
AtmosPure Re-Gen Gas Purifier 115 V 5121810 3644-18 Login
AtmosPure Re-Gen Gas Purifier (International) 5121831
5121835
5121840
5121845		 3644-18-220 Login
  AtmosPure Roughing Prefilter Kit
to filter the glove box's inlet and outlet as the inert gas is purified. Two roughing prefilters, clamp plates for mounting inside Protector Controlled Atmosphere Glove Boxes. AtmosPure P100 Particulate Filter Kit- to filter the glove box's inlet and outlet as the inert gas is purified. Two P100 particulate filters, mount housings.
Labconco # Cat. # $/Each
5441500 3644-20 Login
     
AtmosPure P100 Particulate Filter Kit
to filter the glove box's inlet and outlet as the inert gas is purified. Two P100 particulate filters, mount housings.
Labconco # Cat. # $/Each
5441600 3644-21 Login
  AtmosPure Regeneration Tubing Kit
to make the regeneration plumbing connections to the 4% hydrogen/inert gas mixture, vacuum and vent. Includes flexible tubing and fittings.
Labconco # Cat. # $/Each
5441700 3644-22 Login
     
AtmosPure Flex Tubing Kit
includes the plumbing to make the connection from the AtmosPure to the glove box. 3/4" (19 mm) ID neoprene-lined flexible tubing. For use with all Protector and Precise glove boxes, single width and double width
  Labconco # Cat. # $/Each
Single 5441800 3644-23 Login
Double 5441801 3644-24 Login
  AtmosPure Hard Tubing Kit
includes the plumbing to make the connection from the AtmosPure to the glove box. Stainless steel tubing. For use with all Protector and Precise glove boxes, single width.
  Labconco # Cat. # $/Each
Single 5441802 3644-25 Login
Double 5441803 3644-26 Login
     
AtmosPure Elbow Adapter Kit
AtmosPure 3/4" to 3/8" (19 mm to 10 mm) Adapter Kit. Fittings permit 3/4" ID (19 mm) neoprene hose (not included) to attach to Precise Glove Box's 3/8" (10 mm) inlet/outlet. Two elbows.
Labconco # Cat. # $/Each
5441900 3644-27 Login
   
     
AtmosPure 6-Pin Communication Cable
is required for use when the AtmosPure and glove box configured with Auto Pressure Controller are sharing one vacuum pump.
Labconco # Cat. # $/Each
5442000 3644-28 Login
  AtmosPure 9-Pin Oxygen/Moisture Cable
is required for use when the AtmosPure is used in AUTO mode. Allows for automatic control of the AtmosPure blower from an accessory Oxygen or Mositure Monitor (not included).
Labconco # Cat. # $/Each
5442100 3644-29 Login
     
HEPA Filter Vacuum
HEPA filtered vacuum trap for filtering particulates before entry in to vacuum pump. One HEPA filter, and filter housing for connection with vacuum tubing between glove box and vacuum pump.
Labconco # Cat. # $/Each
5441400 3644-19 Login
  Glove Box Moisture Monitor
Moisture monitor measures dew point range from -80 to 0°C or 0 to 6000 ppm. Displays dew point only. Includes meter, probe and calibration stand. For placement inside the glove box's main chamber. .
Labconco # Cat. # $/Each
5442200 3644-30 Login
     
Exterior Monitor Tubing Kit
provides attachment tubing to allow placement of Moisture Monitor 5244900 or 5244901 outside the glove box.
Labconco # Cat. # $/Each
5442400 3644-31 Login
5442500 3644-32 Login
   
Click to leave a message. 24-hour sales and tech phone support, M - F
Technical Questions?
Schedule a call with a
Terra tech specialist.