Gallery

Gas-Purged Plastic Glove Box Isolator

Gas-purged plastic glove box isolators provide an inert, positive pressure work space. The automatic humidity control module regulates the flow of dry nitrogen gas down to 0% RH. An inert gas airlock minimizes cross-contamination during material transfer. The rear panel is removable to easily transfer large equipment.

Plexiglass Glovebox Terrarium

Series 100 SDPVC Glovebox Used to Test Optical Assemblies

This Series 100 SDPVC glovebox is used to test optical assemblies. The Humex 2 humidifier releases a controlled volume of water vapor into the glovebox to achieve above-ambient humidity levels. Static-dissipative PVC construction prevents static-clinging of particulates.

Laboratory Glove Box in SD-PVC Used to Weigh Sensitive Petrochemicals and Polymers

Maintain a dry, ESD-safe chamber while weighing sensitive petrochemicals and polymers with this SD-PVC laboratory glove box.

Polypropylene Gas-Purged Glovebox for Electrochromic Material Development

Applications using reactive chemical agents and harsh cleaning solvents, such as those involved in developing electrochromic devices, necessitate a chemical-resistant polypropylene glovebox isolator.

ESD-Safe Laboratory Glovebox for Research with Volatile Powders Under Low Humidity

This ESD-safe laboratory glovebox is used for research with volatile powders under low humidity. The automatic nitrogen purge control on top helps conserve N2 gas from the cylinder.

Chemical Resistant Polypropylene Glovebox for Weighing Pharmaceutical Samples

This chemical resistant Series 100 glovebox is used for weighing pharmaceutical samples. The glovebox contains 4 glove ports to accommodate multiple operators. Positive-pressure protects contamination-sensitive materials inside the isolator.

ESD-Safe ULPA Filtered Glovebox for Curing and Drying Samples

This ESD-Safe ULPA filtered glovebox is used for curing and drying samples. This design can be configured for either open loop (single pass) or closed loop (recirculating) operation.

Custom 600 Series Polycarbonate Glovebox with Tilt-Up Window and Electrical Wire Feedthroughs

Custom polycarbonate glovebox with front tilt-up window and wire feedthroughs. Includes a right-mounted airlock and two 10" ABX plastic ports for a wide range of motion within the unit.

Gas-Purged Plastic Glove Box Isolator

A gas-purged glovebox for the manufacture of small semiconductor electrical parts in a low-oxygen, low-moisture environment. Constructed of static-dissipative PVC to protect against ESD.

Custom Single Glovebox, Polycarbonate Series 100

Polycarbonate glovebox includes 3 cord ports located on the rear wall for air hoses and cables. Chamber is for positive-pressure operation with RB valves to relieve over-pressurization. Dual access doors permit introduction of small and large equipment.

Plastic Glove Box Isolator for Cooling Surfaces with Liquid Nitrogen

This plastic glove box isolator is used for cooling surfaces with liquid nitrogen. The automatic nitrogen gas purge, ionizing bar, and static-dissipative PVC shell helps maintain a dry, ESD-safe environment.

Custom Acrylic Glovebox

Glovebox isolators can be custom built for any application; choose any size and configuration.

Customized to Your Requirements!

Custom work is no problem! Shown: nitrogen-purged static-dissipative PVC glovebox isolator for up to six operators working at individual test/assembly stations. Configured with automated gas controls and ionizing bars.

4-Port Glovebox for Semiconductor Work

The 4-port glovebox controls processing for testing and manufacturing operations, and especially comes handy in applications for semiconductor work. Transparent static-dissipative PVC helps control static charges and particles to ensure a sterile work process.

Static-Dissipative PVC Dry Glovebox for Weighing Chemicals

Dry glovebox constructed from contamination and ESD-safe static-dissipative PVC panels. Features side airlock for increased contamination prevention. Unit provides a low-humidity processing environment for weighing minute amounts of chemical reagents.

Custom Polycarbonate Single User Glove Box for Biological Research, In Use

Polycarbonate single model glove box with NitroWatch™ and DualPurge™ humidity controllers for low-moisture environment biological research. Iris ports and side doors allow for the use of electronic equipment during operation.

Negative Pressure Acrylic Glovebox for Silicon Wafer Processing

Negative pressure glovebox in economical acrylic with airlock to preserve chamber pressure while introducing new material. Connected vacuum pump allows for rapid air removal. Suitable for silicon wafer processing.

Custom Polycarbonate Single Glove Box for Biological Research

Polycarbonate single model glove box for biological research. Self-closing Iris ports in the front and back allow for electric cord access and side doors permit introduction of small and large equipment.

Low Humidity Glovebox with Footswitch-Activated Pneumatic Doors

Low humidity glovebox isolator with footswitch-activated pneumatic doors to simplify transfer of large parts through antechambers

Gas-Purged Plastic Glovebox Isolator for Preparing Non-Hazardous Pharmaceuticals

Glovebox isolators are suitable for applications involving powders and particulate-shedding material, as in mixing pharmaceutical compounds. Two side doors and a removable back panel give access to essential equipment.

Twin Polypropylene Glovebox Isolator in an Engineering Lab

A gas-purged plastic glovebox isolator will readily find use in an engineering lab. Polypropylene is excellent for applications involving corrosive acids, such as 3D printing. An inert gas airlock allows for streamlined transfer of materials and equipment.

Gas-Purged Plastic Glovebox Isolator for Assembling Semiconductor Components

A benchtop glovebox isolator with an automatic inert gas humidity-purge system is the right solution for assembling semiconductor components in a controlled environment. An inert gas airlock provides an entry point without compromising the chamber's atmosphere.

Polycarbonate Single-User Inert Gas-Purged Glovebox Isolator with Side Airlock

A basic laboratory gas-purged glovebox will satisfy most requirements when handling sensitive materials. The polycarbonate body is more impact- and chemical-resistant than acrylic. Works well with optional humidity modules to automatically regulate relative humidity.

Basic Twin Laboratory Glovebox Isolator with Tilt-Up Window for Pharmaceutical Compounding

This custom glovebox isolator is used for pharmaceutical compounding. An ionizing bar mounted on top neutralizes static charge. The large tilt-up window facilitates transfer of bulky equipment.

Series 100 SD-PVC Glovebox Isolator for ESD-Testing Products

A glovebox isolator in static-dissipative PVC, shown with separate humidity readers, used to ESD-test products. The SD-PVC panels and grounding safely reduce static charge buildup. Dry inert gas lowers relative humidity inside the chamber.

Glovebox Isolator with 4 Ports for Two Operators

Glovebox isolator features 4 ports for two operators to work from opposite sides. The side panels are removable to allow transfer of large objects that won't fit through the side doors. Designed for use with Terra’s Nitrogen Purge RH control system

Critical Environment Solutions

Terra's mission is to help customers in highly regulated industries transform the world with critical environment solutions that improve health, safety, performance, and yields. These environments may comply with stringent UL, ISO, IEST, ASTM and OSHA standards and local requirements.

Series 100 Polycarbonate 4 Glove Glovebox

Polypropylene Glove Box with Glass Window, Twin Model

Polypropylene laboratory glove box for inert gas bleeding includes four 10" (254 mm)-diameter glove ports and dual-side stainless steel-reinforced access doors (shown with optional air lock).