FREE CONSULTATION714-578-6100
  1. Home
  2. Laminar Flow Hoods, Fume Hoods, Biosafety Cabinets
  3. Laboratory Fume Hoods
  4. Labconco Protector XStream Fume Hood

Protector XStream Laboratory Fume Hoods
by Labconco

labconco protector xstream lab fume hoods
Maximum containment in a laboratory while saving you energy and money
CE 230 Volt Models Only   cleanliness high
UL logo All Models  
  • High-performance, low-volume and energy efficient benchtop models available in 4', 5', 6' and 8' nominal widths
  • Upper Dilution Air Supply eliminates need of additional blowers by bathing the sash interior with clean air
  • Rear Downflow Dual Baffle System: primary baffle directs non-turbulent stream airflow in a single pass from the hood face into the baffle; secondary baffle prevents airflow roll by counteracting upward airstream and forcing air flow downward before exhausting
  • Clean-Sweep™ Sash Handle directs chemical fume concentration away from user's breathing zone by bleeding air into the hood chamber with minimum turbulence via the slim-line radiused sash handle
  • Opti-Zone™ lowers standard face velocity variations in comparison with other baffles as designed slot pattern and sizes increase velocities in the middle and at work surface
  • Eco-Foil™ Air Foil lower energy usage by 7 – 10% compared to flat air foils
  • Cord-Keeper™ Slots located on left and right side of air foil
  • Manufacturer Warranty: One-Year from date of installation or Two-Years from date of shipment
  • Accessories: Cabinets, Protector Solvent Cabinets, Protector Standard Storage Cabinets, Coated Steel Remote Blowers, Fiberglass Blowers and PVC Blowers
Ordering Information

4' Protector XStream Laboratory Hood Models

  • Dimension: 48.0" w x 37.7" d x 59.0" h (1220 x 958 x 1499 mm)
  • Weight: 440.0 lbs. (200.0 kg)
  • Nominal Width: 4 ft.—Enclosure Height: 59.0"
Labconco Part # Total Exhaust CFM and Static Pressure Sash Opening Electrical Cat. # Price
100% (28") Open 62.5% (18") Open
CFM s.p. CFM s.p.
4’ Protector XStream Laboratory Hood
110410000 705 0.26 440 0.10 100 – 115 volts,
50/60 Hz, 10 amps
1538-30 $ 7,024
110410020 705 0.26 440 0.10 208 – 230 volts,
50/60 Hz, 5 amps
1538-31 $ 6,304
4' Protector XStream Laboratory Hood with 2 Service Fixtures
110410021 705 0.26 440 0.10 208 – 230 volts,
50/60 Hz, 5 amps
1538-32 $ 6,878
4' Protector XStream Laboratory Hood with 2 Service Fixtures and 1 electrical duplex
110410002 705 0.26 440 0.10 100 – 115 volts,
50/60 Hz, 10 amps
1538-33 $ 7,024
See Blower Selection Chart

5' Protector XStream Laboratory Hood Models
  • Dimensions: 60.0" w x 37.7" d x 59.0" h (1524 x 958 x 1499 mm)
  • Weight: 525.0 lbs (238.0 kg)
  • Nominal Width: 5 ft.—Enclosure Height: 59"
Labconco Part # Total Exhaust CFM and Static Pressure Sash Opening Electrical Cat. # Price
100% (28") Open 62.5% (18") Open
CFM s.p. CFM s.p.
5' Protector XStream Laboratory Hood
110510000 930 0.32 580 0.12 100 – 115 volts,
50/60, 10 amps
1538-34 $ 7,054
110510020 930 0.32 580 0.12 208 – 230 volts,
50/60 Hz, 5 amps
1538-35 $ 7,054
5' Protector XStream Laboratory Hood with 2 Service Fixtures
110510021 930 0.32 580 0.12 208 – 230 volts,
50/60 Hz, 5 amps
1538-36 $ 7,628
5' Protector XStream Laboratory Hood with 2 service fixtures and 1 Electrical Duplex
110510002 930 0.32 580 0.12 100 – 115 volts,
50/60 Hz, 10 amps
1538-37 $ 7,774
See Blower Selection Chart

6' Protector XStream Laboratory Hood Models
  • Dimension: 72.0" w x 37.7" d x 59.0" h (1829 x 958 x 1499 mm)
  • Weight: 600.0 lbs. (272.0 kg)
  • Nominal Width: 6 ft.—Enclosure Height: 59.0"
Labconco Part # Total Exhaust CFM and Static Pressure Sash Opening Electrical Cat. # Price
100% (28") Open 62.5% (18") Open
CFM s.p. CFM s.p.
6' Protector XStream Laboratory Hood
110610000 1150 0.41 720 0.16 100 – 115 volts,
50/60 Hz, 10 amps
1538-38 $ 7,808
110610020 1150 0.41 720 0.16 208 – 230 volts,
50/60 Hz, 5 amps
1538-39 $ 7,808
6' Protector XStream Laboratory Hood with 2 Service Fixtures
110610021 1150 0.41 720 0.16 208 – 230 volts,
50/60 Hz, 5 amps
1538-40 $ 8,382
6' Protector XStream Laboratory Hood with 2 service fixtures and 1 Electrical Duplex
110610002 1150 0.41 720 0.16 100 – 115 volts,
50/60 Hz, 10 amps
1538-41 $ 8,528
See Blower Selection Chart

8' Protector XStream Laboratory Hood Models
  • Dimensions: 96.0" w x 37.7" d x 59.0" h (2438.5 x 958 x 1499 mm)
  • Weight: 770.0 lbs. (349.0 kg)
  • Nominal Width: 8 ft.—Enclosure Height: 59.0"
Labconco Part # Total Exhaust CFM and Static Pressure Sash Opening Electrical Cat. # Price
100% (28") Open 62.5% (18") Open
CFM s.p. CFM s.p.
8' Protector XStream Laboratory Hood
110810000 1600 0.29 1000 0.11 100 – 115 volts,
50/60 Hz, 10 amps
1538-42 $ 11,119
110810020 1600 0.29 1000 0.11 208 – 230 volts,
50/60 Hz, 5 amps
1538-43 $ 11,119
8' Protector XStream Laboratory Hood with 2 Service Fixtures
110810021 1600 0.29 1000 0.11 208 – 230 volts,
50/60 Hz, 5 amps
1538-44 $ 11,689
8' Protector XStream Laboratory Hood with 2 service Fixtures and 1 Electric Duplex
110810002 1600 0.29 1000 0.11 100 – 115 volts,
50/60 Hz, 10 amps
1538-45 Price
See Blower Selection Chart
Additional Features:
  • Meets SEFA-1 low velocity hood standards when subjected to ASHRAE 110 test protocol
  • Yields lowest required CFM and sets new standard of safety by performing maximum containment under adverse conditions
  • Chemical-resistant, fiberglass-reinforced, composite panel liner and baffles with flame spread index less than 25 per ASTM E84
  • 37.5" (953 mm) high sightline from work surface to header panel
  • Removable front and side panels; plumbing and electrical wiring access from front and interior service panels
  • T8 fluorescent lighting (pre-wired) with vapor-proof design
  • ADA-compliant light and blower switches
  • Sash stop located at 18" (457.2 mm) sash opening position
  • Powder-coated stainless steel, 12.81" (325.37 mm) ID exhaust connection(s); glacier white powder-coated steel exterior; powder-coated sash handle; tempered safety glass vertical-rising sash
  • Contributes to LEED® credits for new construction as designated by United States Green Building Council
  • Compliance: SEFA 1-2010, NFPA 45-2011, ASTM E84-09C, ASHRAE 110-1995, ANSI Z9.5-2011, UL 61010-1\, CAN/CSA C22.2 No. 61010-1, UL 1805, CE Conformity Marking (230 volt models), SEFA 8-2010—Cabinet Surface Finish Tests
  • Required Accessories: Remote Blowers, Ductwork, SpillStopper™ Work Surfaces, Base Cabinets, Adjustable Height Base Stands
  • Optional Accessories: Service Fixture Kits, Electrical Duplex Kits, Airflow Monitors, Distillation Grids, Snuffer™ Fire Extinguisher, Ceiling Enclosure, Rear Finish Panels

Description: http://www.labconco.com/images/cms/extralarge/work_surfaces.jpg   Spillstopper Work Surfaces
  • Available in 4', 5', 6', and 8' nominal width work surfaces
  • Made with corrosion resistant epoxy resins
  • Dished and contoured to conform to interior liner of Protector XStream Laboratory Hoods
  • Large radius of front edge aerodynamically directs airflow into fume hood
  • Pre-drilled holes provided for venting and plumbing pass throughs
  • Select Models include 6" x 3" cupsink cutout
4’ Spillstopper Work Surface, 36" Interior Depth
  • For use with Protector XStream
  • Dimensions: 48.0" w x 36.0" d x 1.25" h
    (1219.5 x 914.5 x 31.75 mm)
  • Hood, Enclosure or Glove Box Width: 4'
  • Weight: 120 lbs. (54.0 kg)
Labconco Part # Cupsink Cutouts Cat. # Price
9503400 None 3651-23 Price
9503401 Right Rear 3651-24 Price
9503402 Right side. Not for use with Protector Solvent Storage Cabinets 3651-25 Price
9503410 Left rear 3651-26 Price
9503411 Left and right rear 3651-27 Price
9503412 Left rear and right side. Not for use with Protector Solvent Storage Cabinets 3651-28 Price
9503420 Left side. Not for use with Protector Solvent Storage Cabinets. 3651-29 Price
9503421 Left side and right rear. Not for use with Protector Solvent Storage Cabinets 3651-30 Price
9503422 Left and right side. Not for use with Protector Solvent Storage Cabinets 3651-31 Price
5’ Spillstopper Work Surface, 36" Interior Depth
  • For use with Protector XStream Laboratory Hoods
  • Dimensions: 60.0" w x 36.0" d x 1.25" h
    (1524 x 914.5 x 31.75 mm)
  • Hood, Enclosure or Glove Box Width: 5'
  • Weight: 160 lbs.(73 kg)
Labconco Part # Cupsink Cutouts Cat. # Price
9503500 None 3651-32 Price
9503501 Right Rear 3651-33 Price
9503502 Right side. Not for use with Protector Solvent Storage Cabinets 3651-34 Price
9503510 Left rear 3651-35 Price
9503511 Left and right rear 3651-36 Price
9503512 Left rear and right side. Not for use with Protector Solvent Storage Cabinets 3651-37 Price
9503520 Left side. Not for use with Protector Solvent Storage Cabinets. 3651-38 Price
9503521 Left side and right rear. Not for use with Protector Solvent Storage Cabinets 3651-39 Price
9503522 Left and right side. Not for use with Protector Solvent Storage Cabinets 3651-40 Price
6’ Spillstopper Work Surface, 36" Interior Depth
  • For use with Protector XStream Laboratory Hoods
  • Dimensions: 72.0" w x 36.0" d x 1.25" h
    (1829 x 914.5 x 31.75 mm)
  • Hood, Enclosure or Glove Box Width: 6'
  • Weight: 220 lbs. (100 kg)
Labconco Part # Cupsink Cutouts Cat. # Price
9503600 None 3651-41 Price
9503601 Right Rear 3651-42 Price
9503602 Right side. Not for use with Protector Solvent Storage Cabinets 3651-43 Price
9503610 Left rear 3651-44 Price
9503611 Left and right rear 3651-45 Price
9503612 Left rear and right side. Not for use with Protector Solvent Storage Cabinets 3651-46 Price
9503620 Left side. Not for use with Protector Solvent Storage Cabinets. 3651-47 Price
9503621 Left side and right rear. Not for use with Protector Solvent Storage Cabinets 3651-48 Price
9503622 Left and right side. Not for use with Protector Solvent Storage Cabinets 3651-49 Price
8’ Spillstopper Work Surface, 36" Interior Depth
  • For use with Protector XStream Laboratory Hoods
  • Dimensions: 96.0" w x 36.0" d x 1.25" h.
    (2438.5 x 914.5 x 31.75 mm)
  • Hood, Enclosure or Glove Box Width: 8'
  • Weight: 250 lbs. (113 kg)
Labconco Part # Cupsink Cutouts Cat. # Price
9503800 None 3651-50 Price
9503801 Right Rear 3651-51 Price
9503802 Right side. Not for use with Protector Solvent Storage Cabinets 3651-52 Price
9503810 Left rear 3651-53 Price
9503811 Left and right rear 3651-54 Price
9503812 Left rear and right side. Not for use with Protector Solvent Storage Cabinets 3651-55 Price
9503820 Left side. Not for use with Protector Solvent Storage Cabinets. 3651-56 Price
9503821 Left side and right rear. Not for use with Protector Solvent Storage Cabinets 3651-57 Price
9503822 Left and right side. Not for use with Protector Solvent Storage Cabinets 3651-58 Price

Required Accessories
Cabinets
Protector Acid Storage Cabinets
Protector Acid Storage Cabinets
 

Protector Acid Storage Cabinets

  • Compatible with: Protector XL Benchtop, Protector Premier, XStream, ClassMate, Stainless Steel, and PVC; and HOPEC IV; Basic and Fiberglass 30 Hoods
  • Safely stores corrosive liquids and acids
  • Made with Durable epoxy-coated steel construction; interior made with corrosion-resistant polyethylene
  • Glacier white exterior coordinates with Labconco fume hoods and laboratory casework
  • Includes: Vacuum-formed PVC liner tray, four leveling feet and one 8" filler panel to cabinet depth from 22" to 30"
  • Max. Load Support: 800 lbs.
  • Filler Panel Depth: 8.0" (203.2 mm)
  • Glacier white exterior coordinates with laboratory casework and other Labconco fume hoods
  • Required Accessories: SpillStopper™ Work Surfaces and Flat Work Surfaces
  • Optional Accessories: Vent Kits, Shelf Kits, Filler Panels
  • ADA-Compliant (Select Models)
     
Labconco
Part #
Dimensions
W x D
Max./Min.
Base Height
ADA Compliant Door Weight Cat. # Price
9905000 24" x 22"
(610 x 559 mm)
32.75"
(832 mm)/
31.5"
(800.1 mm)
Yes Single, Right Hinge, Manual Close 120 lbs.
(54 kg)
3649-49 Price
9905100 18" x 22"
(457.2 x 559 mm)
Yes Single, Right Hinge, Manual Close 85 lbs.
(39 kg)
3649-50 Price
9905200 24" x 22"
(610 x 559 mm)
Yes Single, Left Hinge, Manual Close 120 lbs.
(54 kg)
3649-51 Price
9905300 18" x 22"
(457.2 x 559 mm)
Yes Single, Left Hinge,
Manual Close
85 lbs.
(39 kg)
3649-52 Price
9901000 48" x 22"
(1219.5 x 559 mm)
36.75"
(933.5 mm)/
35.5"
(902 mm)
No Dual, Manual Close 260 lbs.
(118 kg)
3649-53 Price
9901100 36" x 22"
(914.5 x 559 mm)
No Dual, Manual Close 180 lbs.
(82 kg)
3647-23 Price
9901200 30" x 22"
(762 x 559 mm)
No Dual, Manual Close 155 lbs.
(70 kg)
3646-51 Price
9901300 24" x 22"
(610 x 559 mm)
No Single, Right Hinge, Manual Close 130 lbs.
(59 kg)
3649-54 Price
9901400 18" x 22"
(457.2 x 559 mm)
No Single, Right Hinge, Manual Close 90 lbs.
(41 kg)
3649-55 Price
9901500 24" x 22"
(610 x 559 mm)
No Single, Left Hinge,
Manual Close
130 lbs.
(59 kg)
3649-56 Price
9901600 18" x 22"
(457.2 x 559 mm)
No Single, Left Hinge,
Manual Close
90 lbs.
(41 kg)
3649-57 Price
Protector Solvent Storage Cabinets  

Protector Solvent Storage Cabinets

  • Compatible with: Protector XL Benchtop, Protector Premier, XStream, ClassMate, Stainless Steel, and PVC; HOPEC IV; Basic and Fiberglass 30 Hoods
  • Stores and vents flammable liquids and solvents
  • Made with durable dual wall epoxy-coated steel construction with 1.5" air gap
  • Includes: Epoxy-coated steel shelf; Two rear vent connections with flame arrestors and closure plugs; Four leveling feet and one 8" filler panel to increase cabinet depth from 22" to 30"
  • Max. Load support: 800 lbs.
  • Filler Panel Depth: 8.0" (203.2 mm)
  • Glacier white exterior coordinates with laboratory casework and other Labconco fume hoods
  • Required Accessories: SpillStopper™ Work Surfaces and Flat Work Surfaces
  • Optional Accessories: Shelf Kits, Filler Panels ADA-Compliant
  • Select models ADA compliant
    Top of page
Labconco
Part #
Dimensions
W x D
Max./Min.
Base Height
ADA
Compliant
Door Weight Cat. # Price
9906000 24" x 22"
(610 x 559 mm)
32.75"
(832 mm)/
31.5"
(800.1 mm)
Yes Single, Right Hinge,
Manual Close
120 lbs.
(54 kg)
3649-58 Price
9906100 24" x 22"
(610 x 559 mm)
Yes Single, Left Hinge,
Manual Close
120 lbs.
(54 kg)
3649-59 Price
9906200 24" x 22"
(610 x 559 mm)
Yes Single, Right Hinge,
Automatic Close
120 lbs.
(54 kg)
3649-60 Price
9906300 24" x 22"
(610 x 559 mm)
Yes Single, Left Hinge,
Automatic Close
120 lbs.
(54 kg)
3649-61 Price
9902000 48" x 22"
(1219.5 x 559 mm)
36.75"
(933.5 mm)/
35.5"
(902 mm)
No Dual, Manual Close 260 lbs.
(118 kg)
3649-62 Price
9902100 36" x 22"
(914.5 x 559 mm)
No Dual, Manual Close 180 lbs.
(82 kg)
3649-63 Price
9902200 30" x 22"
(762 x 559 mm)
No Dual, Manual Close 155 lbs.
(70 kg)
3649-64 Price
9902300 24" x 22"
(610 x 559 mm)
No Single, Right Hinge,
Manual Close
130 lbs.
(59 kg)
3649-65 Price
9902400 24" x 22"
(610 x 559 mm)
No Single, Left Hinge,
Manual Close
130 lbs.
(59 kg)
3649-66 Price
9903000 48" x 22"
(1219.5 x 559 mm)
No Dual, Automatic Close 260 lbs.
(118 kg)
3646-04 Price
9903100 36" x 22"
(914.5 x 559 mm)
No Dual, Automatic Close 180 lbs.
(82 kg)
3646-09 Price
9903200 30" x 22"
(762 x 559 mm)
No Dual, Automatic Close 155 lbs.
(70 kg)
3646-52 Price
9903300 24" x 22"
(610 x 559 mm)
No Single, Right Hinge,
Automatic Close
130 lbs.
(59 kg)
3649-67 Price
9903400 24" x 22"
(610 x 559 mm)
No Single, Left Hinge,
Automatic Close
130 lbs.
(59 kg)
3649-68 Price
Protector Standard Storage Cabinets
48" wide (9900000) with Dual Doors
Protector Standard Storage Cabinets
24" Wide; Right Hinge, Single Door (9904000) ADA Compliant

 

Protector Standard Storage Cabinets

  • Compatible with: Protector XL Benchtop, Protector Premier, XStream, ClassMate, Stainless Steel, and PVC; HOPEC IV; Basic and Fiberglass 30 Hoods
  • Stores and vents flammable liquids and solvents
  • Made with durable dual wall epoxy-coated steel construction with 1.5" air gap
  • Includes: Epoxy-coated steel shelf; Two rear vent connections with flame arrestors and closure plugs; Four leveling feet and one 8" filler panel to increase cabinet depth from 22" to 30"
  • Max. Load support: 800 lbs.
  • Filler Panel Depth: 8.0" (203.2 mm)
  • Glacier white exterior coordinates with laboratory casework and other Labconco fume hoods
  • Required Accessories: SpillStopper™ Work Surfaces and Flat Work Surfaces
  • Optional Accessories: Shelf Kits, Filler Panels ADA-Compliant
  • Select models ADA compliant
    Top of page
Labconco
Part #
Dimensions
W x D
Max./Min.
Base Height
ADA
Compliant
Door Weight Cat. # Price
9904000 24" x 22"
(610 x 559 mm)
32.75"
(832 mm)/
31.5"
(800.1 mm)
Yes Single, Right Hinge, Manual Close 120 lbs.
(54 kg)
3649-69 Price
9904100 18" x 22"
(457.2 x 559 mm)
Yes Single, Right Hinge, Manual Close 85 lbs.
(39 kg)
3649-70 Price
9904200 12" x 30"
(305 x 762 mm)
Yes Single, Right Hinge, Manual Close 60 lbs.
(27 kg)
3649-71 Price
9904300 24" x 22"
(610 x 559 mm)
Yes Single, Left Hinge,
Manual Close
120 lbs.
(54 kg)
3649-72 Price
9904400 18" x 22"
(457.2 x 559 mm)
Yes Single, Left Hinge,
Manual Close
85 lbs.
(39 kg)
3649-74 Price
9904500 12" x 30"
(305 x 762 mm)
Yes Single, Left Hinge,
Manual Close
60 lbs.
(27 kg)
3649-75 Price
9900000 48" x 22"
(1219.5 x 559 mm)
36.75"
(933.5 mm)/
35.5"
(902 mm
No Dual, Manual Close 260 lbs.
(118 kg)
3646-03 Price
9900100 36" x 22"
(914.5 x 559 mm)
No Dual, Manual Close 180 lbs.
(82 kg)
3646-08 Price
9900200 30" x 22"
(762 x 559 mm)
No Dual, Manual Close 155 lbs.
(70 kg)
3646-53 Price
9900300 24" x 22"
(610 x 559 mm)
No Single, Right Hinge, Manual Close 130 lbs.
(59 kg)
3649-54 Price
9900400 18" x 22"
(457.2 x 559 mm)
No Single, Right Hinge, Manual Close 90 lbs.
(41 kg)
3649-76 Price
9900500 12" x 30"
(305 x 762 mm)
No Single, Right Hinge, Manual Close 65 lbs.
(29 kg)
3649-77 Price
9900600 24" x 22"
(610 x 559 mm)
No Single, Left Hinge,
Manual Close
130 lbs.
(59 kg)
3649-78 Price
9900700 18" x 22"
(457.2 x 559 mm)
No Single, Left Hinge,
Manual Close
90 lbs.
(41 kg)
3649-79 Price
9900800 12" x 30"
(305 x 762 mm)
No Single, Left Hinge,
Manual Close
65 lbs.
(29 kg)
3649-80 Price
Top of page

Coated Steel Remote BlowersModerate to highly corrosive hood applications
 

Coated Steel Remote Blowers

  • For use with Labconco Laboratory fume hoods, canopy-ducted Type A2 cabinets and required for Type B2 cabinets
  • Low to moderately corrosive hood applications
  • Flow-through vent holes and louvers cools motor by circulating air; extends motor life
  • Material: corrosion resistant phenolic-coated impeller and housing; powder-coated steel base resist extreme weather
  • Includes removable weather cover for easy lubrication; sheave alignment enhances performance and extends motor life
  • Motor: belt-drive with adjustable sheave and self-adjusting gravity belt tightener
  • Durable and easy maintenance with factory lubricated pillow block bearings
  • Flexible installation with adjustable variable exhaust orientation (adjusts to 8 outlet positions)
  • Quiet operation and optimum air delivery with balanced air impellers
  • Quiet operation: 64-88 decibels depending on blower size
  • Meets demanding daily ventilation requirements of various hood types
  • Available in a wide range of capacities from 370 to 1960 CFM at static pressures to 1.50" H20
  • Contact a Terra product expert for electrical configurations
  • *Power Cord & Plug: 8', 3-wire cord, and plug
  • Manufacturer Warranty: One year parts and labor from date of installation or two years from date of shipment.
    Top of page
Labconco Part # Weight Electrical Inlet/
Outlet
RPM
Range
HP CFM Range Cat. # Price
7068000 92 lbs.
(42 kg)
115 V, 60 Hz,
1 phase, 4.0 amps
10.78" ID/5.5" d x 10.00" w 529-807 1/6 Less than 1000 3645-52 Price
7068200 92 lbs.
(42 kg)
115V, 60 Hz,
1 phase, 4.4 amps
752-1067 1/4 Less than 1000 3645-53 Price
7068400 86 lbs.
(39 kg)
115V, 60 Hz, 1 phase, 6.1 amps 929-1260 1/3 Less than 1000 3650-35 Price
7068600 88 lbs.
(40 kg)
115V, 60 Hz, 1 phase, 8.4 amps 1073-1456 1/2 Less than 1000 3650-36 Price
7068800 90 lbs.
(41 kg)
115V, 60 Hz, 1 phase, 6.1 amps 12.25" OD/
7" d x 13.50" w
373-569 1/3 Less than 1000 3650-37 Price
7069000 96 lbs.
(44 kg)
115V/60 Hz/1Ø/8.4 amps 532-753 1/2 Between 1000 and 2000 3650-38 Price
7069200 100 lbs.
(45 kg)
115V, 11.6amps/
230V, 5.8 amps/60 Hz/1 phase
667-946 3/4 Between 1000 and 2000 3650-39 Price
7069400 100 lbs.
(45 kg)
115V, 13.6 amps/230V, 6.8 amps/60 Hz/1Ø 828-1173 1 Between 1000 and 2000 3650-40 Price
7069600 114 lbs.
(52 kg)
115V, 20.4amps/230V, 10.2 amps/60 Hz/1Ø 881-1248 1 1/2 Between 2000 and 3000 3650-85 Price
Explosion Proof Coated Steel Blowers
7068100 92 lbs.
(42 kg)
115V/60 Hz/1Ø/3.15 amps 10.78" ID/5.5" d x 10.00" w 529-807 1/6 Less than 1000 3650-42 Price
7068300* 92 lbs.
(42 kg)
115V/60 Hz/1Ø/4.5 amps 752-1067 1/4 Less than 1000 3650-43 Price
7068500* 86 lbs.
(39 kg)
115V/60 Hz/1Ø/6.4 amps 929-1260 1/3 Less than 1000 3650-44 Price
7068700 98 lbs.
(44 kg)
115V, 9.0 amps/230V, 4.5 amps/60 Hz/1Ø 1073-1456 1/2 Less than 1000 3650-45 Price
7068900 90 lbs.
(41 kg)
115V/60 Hz/1Ø/6.4 amps 12.25" OD/
7" d x 13.50" w
373-569 1/3 Less than 1000 3650-46 Price
7069100 102 lbs.
(46 kg)
115V, 9.0 amps/230V, 4.5 amps/60 Hz/1Ø 532-753 1/2 Between 1000 and 2000 3650-47 Price
7069300 108 lbs.
(49)
115V, 11.4 amps/230V, 5.7 amps/60 Hz/1Ø 667-946 3/4 Between 1000 and 2000 3650-58 Price
7069500 114 lbs.
(52 kg)
115V, 13.6 amps/230V, 6.8 amps/60 Hz/1Ø 828-1173 1 Between 1000 and 2000 3650-59 Price
7069700 114 lbs.
(52 kg)
230V, 4.8 amps/460V, 2.4 amps/60 Hz/3Ø 881-1248 1 1/2 Between 2000 and 3000 3650-60 Price
7071900 100 lbs.
(45.5 kg)
230V, 5.8 amps/
460V, 2.9 amps,60 Hz
828-1173 1 Between 1000 and 2000 3650-61 Price
Top of page
Fiberglass BlowerModerate to highly corrosive hood applications
 

Fiberglass Blowers

  • For use with Labconco fume hoods and biosafety cabinets
  • Superior corrosion resistance and ideal for moderate to highly corrosive hood applications/conditions; not for use with Perchloric acid
  • Low RPM blowers for quiet operation
  • Material: Molded fiberglass reinforced polyester housing; impellers made of injection-molded polypropylene; dry powder epoxy-coated base and weather cover provide long life
  • Select fiberglass blowers deliver as little as 325 CFM at .12" static pressure or up to 2050 CFM at 4.0" static pressure
  • Air circulation through flow-through vent holes and louvers cools and prolongs motor life
  • Adjustable sheaves for air volume adjustment
  • Bonded impeller reduces maintenance and increases longevity
  • Gravity belt tightener self-adjusts for consistent performance and motor mount secures motor in event of belt failure
  • Required Accessories: Ductwork
  • Flexible installation with variable exhaust adjusting to three outlet positions
  • Depending on blower size, sound levels with 10" and 12" diameter inlets range between 64 and 88 decibels
  • Manufacturer Warranty: One year parts and labor from date of installation or two years from date of shipment.

*Explosion-proof models available with non-sparking polypropylene impellers and explosion proof motors are UL listed for maximum safety.

    Top of page
Labconco Part # Weight Electrical Inlet/
Outlet
RPM
Range
HP CFM Range Cat. # Price
7180000 92 lbs.
(42 kg)
115V/60 Hz/1Ø/4.0 amps 10.38" OD Inlet, 10.75" ID Outlet 630-962 1/6 Less than 1000 3650-86 Price
7180200 92 lbs.
(42 kg)
115V/60 Hz/1Ø/4.4 amps 828-1173 1/4 Less than 1000 3646-57 Price
7180400 86 lbs.
(39 KG)
115V/60 Hz/1Ø/6.1 amps 1073-1456 1/3 Less than 1000 3650-62 Price
7180600 88 lbs.
(40 kg)
115V/60 Hz/1Ø/8.4 amps 1305-1772 1/2 Less than 1000 3650-63 Price
7180800 90 lbs.
(41 kg)
115V/60 Hz/1Ø/4.0 amps 12.38" OD Inlet, 12.75" ID Outlet 373-569 1/6 Less than 1000 3650-64 Price
7181000 96 lbs.
(44 kg)
115V/60 Hz/1Ø/4.4 amps 532-753 1/4 Less than 1000 3650-65 Price
7181200 100 lbs.
(45 kg)
115V/60 Hz/1Ø/8.4 amps 690-978 1/2 Between 1000 and 2000 3650-66 Price
7181400 100 lbs.
(45 kg)
115V, 11.6 amps/230V, 5.8 amps/60 Hz/1Ø 920-1303 3/4 Between 1000 and 2000 3650-67 Price
7181600 114 lbs.
(52 kg)
115V, 20.4 amps/230V, 10.2 amps/60 Hz/1Ø 1207-1639 1 1/2 Between 1000 and 2000 3650-68 Price
7182000 290 lbs.
(132 kg)
208-230V, 6.8 amps/ 460V, 3.4 amps/60 Hz/3Ø 15.63" OD Inlet, 16" ID Outlet 1083-1469 2 Between 2000 and 3000 3650-69 Price
7182200 365 lbs.
(166 kg)
208-230V, 9.7 amps/ 460V, 4.85 amps/60 Hz/3Ø 1309-1777 3 Greater than 3000 3650-70 Price
Explosion Proof Fiberglass Blowers
Labconco Part # Weight Electrical Inlet/
Outlet
RPM
Range
HP CFM Range Cat. # Price
7180100 92 lbs.
(42 kg)
115V/60 Hz/1Ø/3.15 amps 10.38" OD Inlet, 10.75" ID Outlet 630-962 1/6 Less than 1000 3650-71 Price
7180300 92 lbs.
(42 kg)
115V/60 Hz/1Ø/4.5 amps 828-1173 1/4 Less than 1000 3650-73 Price
7180500 86 lbs. (39 KG) 115V/60 Hz/1Ø/6.4 amps 1073-1456 1/3 Less than 1000 3650-72 Price
7180700 98 lbs.
(44 kg)
115V, 9.0 amps/230V, 4.5 amps/60 Hz/1Ø 1305-1772 1/2 Less than 1000 3650-74 Price
7180900 90 lbs.
(41 kg)
115V/60 Hz/1Ø/3.15 amps 12.38" OD Inlet, 12.75" ID Outlet 373-569 1/6 Less than 1000 3650-75 Price
7181100 102 lbs.
(46 kg)
115V/60 Hz/1Ø/4.5 amps 532-753 1/4 Less than 1000 3650-76 Price
7181300 108 lbs.
(49 kg)
115V, 9.0 amps/230V, 4.5 amps/60 Hz/1Ø 690-978 1/2 Between 1000 and 2000 3650-77 Price
7181500 114 lbs.
(52 kg)
115V, 11.4 amps/230V, 5.7 amps/60 Hz/1Ø 920-1303 3/4 Between 1000 and 2000 3650-78 Price
7181700 114 lbs.
(52 kg)
230V, 4.8 amps/460V, 2.4 amps/60 Hz/3Ø 1207-1639 1 1/2 Between 1000 and 2000 3650-79 Price
7182100 345 lbs.
(156 kg)
208-230V, 6.0 amps/ 460V, 3.0 amps/60 Hz/3Ø 15.63" OD Inlet, 16" ID Outlet 1083-1469 2 Between 2000 and 3000 3650-80 Price
7182300 370 lbs.
(168 kg)
208-230V, 8.4 amps/
460V, 4.2 amps/60 Hz/3Ø
1309-1777 3 Greater than 3000 3650-81 Price
Top of page
pvc blowerOptimum chemical resistance in very highly corrosive hood applications
 

PVC Blowers

  • For use with Labconco fume hoods and biosafety cabinets
  • Provides optimum chemical resistance and able to handle perchloric acid and other high order oxidizers; low RPM blowers for quiet operation
  • Designed with drain connection on lower portion of housing to enable use of washdown system
  • Vacuum formed housing made with unplasticized Type I polyvinyl chloride for complete corrosion protection
  • Material: Dry powder epoxy-coated base and weather cover extends blower life in extreme weather; unplasticized Type I polyvinyl chloride housing
  • Adjustable sheaves for air volume adjustment
  • Air circulation through flow-through vent holes and louvers cools and prolongs motor life
  • Injection molded PVDF impellers resist highly corrosive atmospheres
  • Bonded impeller reduces maintenance and increases longevity; easy maintenance with easy access to impeller assembly
  • Gravity belt tightener self-adjusts for consistent performance and motor mount secures motor in event of belt failure
  • Flexible installation with variable exhaust adjusting to three outlet positions
  • Easy installation with inlet and discharge diameters sized to directly receive rigid PVC ducting material
  • Blowers available with 10" and 12" inlet/outlet connections
  • Sound levels: Between 64 and 88 decibels depending on blower size
  • Required Accessories: Ductwork
  • Manufacturer Warranty: One year parts and labor from date of installation or two years from date of shipment.
     
Labconco Part # Weight Electrical Inlet/
Outlet
RPM
Range
HP CFM Range Cat. # Price
7183000 90 lbs. (41 kg) 115V/60 Hz/1Ø/8.4 amps 10.38" OD Inlet, 10.75" ID Outlet 1150-1561 1/2 Less than 1000 3650-82 Price
7183100 90 lbs. (41 kg) 115V/60 Hz/1Ø/8.4 amps 12.38" OD Inlet, 12.75" ID Outlet 881-1248 1/2 Between 1000 and 2000 3650-83 Price
7183200 100 lbs. (45 kg) 115V, 13.6 amps/230V, 6.8 amps/60 Hz/1Ø 1208-1639 1 Between 1000 and 2000 3650-84 Price
Top of page
Protector XStream Laboratory Fume Hoods Dimensions
Top of page
Blower Selection Chart
Determine the blower selection from these exhaust requirements including the total system static pressure loss.
Top of page
How XStream Saves Energy and Money While Reducing Contaminants
  • Draws less air from laboratory environment but keeps contaminant contained
  • Does NOT rely on restricted sash opening, airflow sensors and electronic control, mechanical components or additional fans
  • Patented features significantly reduce the concentration of contaminants behind sash opening
  • Dilutes air supply that lingers behind the sash with clean air
  • Ergonomic air foil with Clean-Sweep™ openings allow air to sweep the work surface
  • Rear downflow dual baffle system directs airflow in nonturbulent laminar flow air streams to the back of the hood and counteracts the tendency for air inside the fume hood to roll forward
  • Containment-enhancing sash handle sweeps airflow into the hood with minimal turbulence
Top of page
You might also like:

File Type File Name Publication Date
Brochure (PDF) Protector Laboratory Fume Hoods Brochure by Labconco
Provides a brief introduction to features and available accessories for Protector Laboratory Fume Hoods by Labconco. Product specifications included.
04/08/2016
White Paper (PDF) Face Velocity Standards, by Labconco
Learn more about fume hoods, specifically the performance of a fume hood — what’s important and how to test for it.
05/18/2015
White Paper (PDF) What Type of Fume Hood do I Specify? By Labconco
Tips and considerations for choosing the best fume hood for your laboratory and applications.
05/18/2015
Click to leave a message. 24-hour sales and tech phone support, M - F
Go to...
Go To
Laboratory-Equipment.com